EVENT LIGHTING APRO4-IP DMX Controller

Per a vostra sicurità, leghjite attentamente stu manuale d'utilizatore prima di l'usu.
Event Lighting si riserva u dirittu di rivisà u manuale in ogni mumentu. L'infurmazioni è e specificazioni in stu manuale sò sottumessi à cambià senza avvisu. Event Lighting ùn assume alcuna responsabilità o rispunsabilità per eventuali errori o omissioni. Per piacè cunsultate Event Lighting per qualsiasi chiarificazione o infurmazione nantu à questu articulu.

CARATTERISTICHE

• DMX 512, RDM, Artnet and sACN support
• Configurazione remota via interna webpagina
• Update firmware on Webpagina
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• Display LCD
• Gigabit network, 100/1000mbps port speed
• Classificazione IP65

PANNELLU FINITUVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Porta fusible
7. LCD Display protection cover

MENUS
Below is controller Menus map

PrincipaleMenu	Sottomenu 1	Sottomenu 2	Valore/Opzione	Default
Rete	Modu IP		DHCP	Staticu
			Staticu
	Indirizzu IP		2.xx.xx.xx	2.xx.xx.xx
	Maschera di Subnet		255.0.0.0	255.0.0.0
Port DMX	Protocolu	Artnet		Artnet
		sACN
	Start Net		000-127	000
	Start Universe		000-255	000
	Portu 1	Modu	Off	On
			On
		NET	000-127	000
		Universu	000-255	000
	Portu 2	Modu	Off	On
			On
		NET	000-127	000
		Universu	000-255	001
	Portu 3	Modu	Off	On
			On
		NET	000-127	000
		Universu	000-255	002
	Portu 4	Modu	Off	On
			On
		NET	000-128	000
		Universu	000-255	003
			Disattivà
Settings	Tariffa DMX		20 Hz	30 Hz
			25 Hz
			30 Hz
			35 Hz
			40 Hz
	RDM	Disattivà		Disattivà
		Attivà
	Mustrà On	Sempre		1 min
		30 sec
		1 min
		5 min
	Perdita di signale	Mantene DMX		Mantene DMX
		Stop Output
	Modu Merge	PH		PH
		LTP
	Reset di fabbrica	Innò		Innò
		Iè

WEB cunfigurazione

NET device network IP mode can set to DHCP mode or Static mode.

Modu DHCP

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Enter IP address in your web browser, then you can login webpage to configure the parameter of controller.

Inserite password: admin

Modu staticu

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Then set the IP address of computer is in the same IP range manually. For example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Inserite password: admin

• When log on NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• For DMX Port page , it is used for DMX Port setting. You can select Protocol to be Artnet or sACN, and set each port as input or output.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Perdita di signale: Can set as Hold DMX or Stop Output.
• You can return to factory setting by click Factory Reset button.
• On Update page, you can update software of fixture by selecting the update software file of APRO4‐IP.
• On the last page, you can reset password.

SPECIFICATION

• Potenza in: AC 100‐240V,50/60Hz
• Cunsumu di energia: AC240V 50HZ 0.05A
• Taglia: 215.3×150.5x42mm 4.2W
• Pesu: 1.43 kg
• POE 802.3af
• IP65

DIMENSIONI

Garanzia

Per piacè riferite à u vostru rivenditore lucali o cuntattate Event Lighting. www.event‐lighting.com.au

Domande Frequenti

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Documenti / Risorse

EVENT LIGHTING APRO4-IP DMX Controller [pdfManuale d'usu APRO4-IP, APRO4-IP DMX Controller, DMX Controller, Controller

Referenze

• Manuale d'usu