HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch (J9803A) User Manual

1. Introduzione

This manual provides detailed instructions for the installation, configuration, and operation of the HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch (Model J9803A). The HP 1810 Switch Series offers smart-managed, fixed-configuration Gigabit Layer 2 switching capabilities, designed for small business environments requiring an easy-to-administer networking solution.

Please read this manual thoroughly before attempting to install or operate the device. Retain this manual for future reference.

2. Cuntenutu di u pacchettu

Carefully unpack the box and verify that all items are present and in good condition. If any item is missing or damaged, contact your vendor immediately.

• HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch (J9803A)
• Cordone d'alimentazione
• Rack-mounting hardware (brackets and screws)
• Documentazione (Guida di avviu rapidu, Informazioni di sicurezza è normative)

Figura 2.1: The retail packaging for the HP 1810-24G v2 Gigabit SFP Rack-Mountable Switch. This box contains the switch unit and all included accessories.

Figura 2.2: Contents of the HP 1810-24G v2 Switch package, including the switch unit, power cord, and rack-mounting brackets with screws.

3. Descrizzione fisica

3.1 Pannellu Frontale

Figura 3.1: Fronte view of the HP 1810-24G v2 Switch, showing the 24 Gigabit Ethernet ports and 2 SFP ports.

The front panel of the HP 1810-24G v2 Switch features the following components:

• 24 x 10/100/1000Base-T Ports: RJ-45 ports for connecting network devices using Ethernet cables. Each port supports auto-negotiation for speed and duplex mode.
• 2 x Gigabit SFP Ports: Small Form-Factor Pluggable ports for fiber optic connections, allowing for extended network reach or uplink to other network devices.
• Indicatori LED: Status LEDs for power, system activity, and individual port status (link/activity, speed).
• Pulsante di reset: Used to reset the switch to factory default settings.

3.2 Panel posteriore

The rear panel typically includes the power input connector and possibly grounding points.

• Ingressu di alimentazione AC: Connettore per u cordone di alimentazione.

4. Setup è Installazione

4.1 Precauzioni di sicurezza

• Assicuratevi chì a fonte d'alimentazione currisponde à u vulume di l'interruttoretage esigenze.
• Ùn bluccate micca l'aperture di ventilazione.
• Avoid placing the switch in direct sunlight or near heat sources.
• Keep the switch away from water or damp ambienti.

4.2 Opzioni di muntatura

The HP 1810-24G v2 Switch supports both rack-mounting and wall-mounting.

4.2.1 Rack Mounting

1. Attach the provided rack-mounting brackets to the sides of the switch using the included screws.
2. Secure the switch into a standard 19-inch equipment rack using appropriate rack screws (not always included).

4.2.2 Muntamentu murale

1. Identify a suitable wall location, ensuring adequate ventilation and access to power.
2. Use appropriate wall anchors and screws (not included) to secure the switch to the wall.

4.3 Cunnessu Power

1. Connect one end of the power cord to the AC power inlet on the rear panel of the switch.
2. Cunnette l'altra estremità di u cavu di alimentazione à una presa elettrica cun messa à terra.
3. Verificate chì u LED di alimentazione nantu à u pannellu frontale s'illumina, chì indica chì l'interruttore riceve alimentazione.

4.4 Cunnessioni di Rete

1. Connect your network devices (computers, servers, access points, etc.) to the RJ-45 Gigabit Ethernet ports using standard Ethernet cables.
2. For fiber optic connections, insert compatible SFP transceivers (not included) into the SFP ports, then connect fiber optic cables.
3. Observe the port LEDs to confirm link status and activity.

5. Operating Instructions

5.1 Cunfigurazione iniziale (Web Interfaccia)

The HP 1810-24G v2 Switch is a smart-managed switch, configurable via a web-interfaccia basata.

1. Connect a computer directly to any RJ-45 port on the switch using an Ethernet cable.
2. Configure your computer's IP address to be in the same subnet as the switch's default IP address (refer to the Quick Start Guide for default IP).
3. apre a web navigatore è inserite l'indirizzu IP predefinitu di u switch.
4. Log in using the default username and password (refer to the Quick Start Guide).
5. Follow the on-screen prompts to change the default password and configure basic network settings, such as the switch's IP address, subnet mask, and gateway.
6. Esplora u web interface for advanced features like VLAN tagging, Link Aggregation (LACP), Spanning Tree Protocol (STP), Quality of Service (QoS), and SNMP.

5.2 Basic Network Operation

Once configured, the switch operates automatically to forward network traffic between connected devices.

• Plug and Play: Connect Ethernet devices to any available port. The switch will automatically detect the connection speed and duplex mode.
• Prestazione Gigabit: Supports Gigabit Ethernet speeds (1000 Mbps) for high-bandwidth applications.
• SFP Connectivity: Utilize SFP ports for fiber uplinks to connect to other switches or network segments over longer distances.

6. Mantenimentu

6.1 Aghjornamenti di u firmware

Periodically check the Hewlett Packard Enterprise (HPE) support websitu per l'aghjurnamenti di u firmware. Mantene u firmware aggiornatu garantisce prestazioni ottimali, sicurezza è accessu à nuove funzionalità.

1. Download the latest firmware from the official HPE support portal.
2. Accede à l'interruttore web interfaccia.
3. Navigate to the firmware upgrade section and follow the instructions to upload and install the new firmware.
4. Nota: Do not power off the switch during a firmware upgrade.

6.2 Pulizia

To maintain proper ventilation and prevent overheating, keep the switch clean.

• Aduprate un pannu dolce è asciuttu per asciugà l'esternu di l'interruttore.
• Use compressed air to clear dust from ventilation openings.
• Ùn aduprate micca detergenti liquidi o aerosol.

6.3 Ripristinazione di i paràmetri di fabbrica

If necessary, the switch can be reset to its factory default settings. This will erase all custom configurations.

1. With the switch powered on, locate the reset button on the front panel.
2. Aduprate una graffetta o un oggettu appuntitu simile per appughjà è tene premutu u buttone di reset per circa 10 secondi.
3. Release the button when the system LEDs indicate a reset (refer to the Quick Start Guide for specific LED behavior).
4. U switch si riavvierà cù i paràmetri di fabbrica.

7. Risoluzione di prublemi

Questa sezione furnisce suluzioni à i prublemi cumuni chì pudete scuntrà.

7.1 Nisun putere

• Ensure the power cord is securely connected to both the switch and a working electrical outlet.
• Verificate chì a presa di corrente funziona cunnettendu un altru apparechju.
• Check the power LED on the front panel. If it is off, contact support.

7.2 Nisuna cunnessione di rete

• Check the Ethernet cables for secure connections at both ends.
• Verify the link/activity LED for the connected port. If it is off, try a different port or cable.
• Ensure the connected device is powered on and configured correctly.
• If using SFP ports, ensure compatible transceivers are used and fiber cables are correctly connected.
• Confirm the switch's IP address and network settings are correct via the web interfaccia.

7.3 Ùn si pò accede Web Interfaccia

• Assicuratevi chì l'indirizzu IP di u vostru urdinatore sia in a listessa sotturete cum'è u switch.
• Verify you are using the correct IP address for the switch.
• Svuotate a cache di u vostru navigatore o pruvate un navigatore diversu.
• If the password was changed and forgotten, you may need to perform a factory reset (see Section 6.3).

8. Specificazioni

9. Garanzia è Support

For warranty information and technical support, please refer to the official Hewlett Packard Enterprise (HPE) websitu o a ducumentazione inclusa cù u vostru pruduttu.

Important Notice Regarding Returns and Warranty: Please be aware that returns for non-defective items may not be accepted. Merchandise returned for repair and found not to be defective by technicians may incur a restocking fee. Additional warranty length options may be available; contact your vendor directly for more details.

Per più assistenza, visitate l'ufficiale Assistenza HPE Websitu.