MTX Audio 5512-22 5500 Series Subwoofer Instruction Manual

1. Introduzione

Thank you for choosing the MTX Audio 5512-22 5500 Series Subwoofer. This 12-inch component subwoofer is engineered to deliver powerful and precise low-frequency sound for your car audio system. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your subwoofer.

Figura 1: Fronte view of the MTX Audio 5512-22 Subwoofer.

2. Informazioni di sicurezza

Please read and understand all instructions before installing and operating this subwoofer. Failure to follow these guidelines may result in injury or damage to the product or vehicle.

• Scollegate sempre a batteria di u veiculu prima di inizià qualsiasi travagliu elettricu.
• Ensure proper wiring and connections to prevent short circuits and electrical hazards.
• Muntate u subwoofer in modu sicuru per impedisce u muvimentu durante u funziunamentu di u veiculu.
• Avoid prolonged exposure to extremely high volume levels, which can cause hearing damage.
• Stu pruduttu cuntene chimichi cunnisciuti da u Statu di California per causà cancer è difetti di nascita o altre dannu riproduttivu.

3. Setup è Installazione

3.1 Unpacking

Carefully remove the subwoofer from its packaging. Inspect for any signs of damage during transit. Retain the packaging for future transport or service needs.

3.2 Connessioni Wiring

The MTX Audio 5512-22 features a dual voice coil design with a 2 Ohm impedance. Proper wiring is crucial for optimal performance and amplifier stability. Consult your amplifier's manual for recommended wiring configurations for a 2 Ohm load.

Figura 2: Posteriore view showing the subwoofer's terminals.

3.3 Raccomandazioni per l'involucri

For best results, install the 5512-22 subwoofer in a sealed or ported enclosure designed for its specifications. The enclosure's volume and port tuning (for ported designs) significantly impact sound quality and output. Refer to specialized car audio resources or professional installers for appropriate enclosure designs.

Figura 3: Side view of the subwoofer, highlighting its robust construction.

3.4 AmpImpostazione di u guadagnu di l'alimentatore

Impostazione di amplifier gain correctly is essential to prevent distortion and potential damage to your subwoofer and amplifier. The gain control is used to match the output voltage of your source unit (head unit) to the input sensitivity of your amplifier, not as a volume control.

To properly set your amplifier's gain, you can use Ohm's Law to calculate the target RMS voltage output. For the 5512-22, with a 400W RMS power rating and 2 Ohm impedance, the desired RMS voltage is approximately 31.62 Volts (V = √(P * R) = √(400W * 2Ω) = √800 ≈ 28.28V, or if using 500W RMS as in the video example, V = √(500W * 2Ω) = √1000 ≈ 31.62V).

A multimeter is required for accurate gain setting. Play a test tone (e.g., 50Hz sine wave) at 0dB from your source unit with the volume set to about 75-80% of maximum. With the subwoofer disconnected from the amplifier, measure the AC voltage à u amplifier's speaker terminals. Adjust the amplifier's gain control until the multimeter reads the calculated target RMS voltage. Ensure all bass boost, subsonic filters, and low-pass filters on the amplifier are set to their minimum or off positions during this process to achieve the widest bandwidth for gain setting.

4. Operazione

Once installed and properly configured, your MTX Audio 5512-22 subwoofer is ready for use. Adjust your head unit's volume and amplifier's filters (low-pass filter, subsonic filter, bass boost) to achieve your desired sound. Start with conservative settings and gradually increase them to avoid overdriving the subwoofer or amppiù vivu.

• Filtru passa-bassu (LPF): This filter allows only frequencies below a set point to pass through to the subwoofer. Typically set between 80Hz and 120Hz, depending on your other speakers.
• Filtru Subsonicu: This filter removes extremely low frequencies that are inaudible and can cause the subwoofer to over-excurt, potentially causing damage. Set it slightly below your enclosure's tuning frequency.
• Bass Boost: Use sparingly. Excessive bass boost can lead to distortion and damage. If more bass is desired, consider adjusting the enclosure or amplifier gain slightly.

5. Mantenimentu

The MTX Audio 5512-22 subwoofer requires minimal maintenance to ensure long-lasting performance.

• Pulizia: Aduprate un pannu dolce è asciuttu per asciugà u conu è u so circondu. Evitate l'usu di prudutti chimichi aggressivi o umidità eccessiva.
• Ispezione: Periodically check all wiring connections for tightness and corrosion. Ensure the subwoofer is securely mounted in its enclosure.
• Evite l'overdriving: Listen for signs of distortion (clipping) from your amplifier or subwoofer. Reduce volume or adjust settings immediately if distortion is heard.

6. Risoluzione di prublemi

Sè avete prublemi cù u vostru subwoofer, riferitevi à i seguenti prublemi è suluzioni cumuni:

• Nisun sonu:
  • Check all power, ground, remote, and signal connections.
  • Verificate amplifier is powered on (power indicator light).
  • Verificate ampfusibili di lificatore.
  • Ensure source unit is providing an audio signal.
• Sonu distortu:
  • Riduce ampguadagnà lificatore.
  • Check for proper impedance matching between subwoofer and amppiù vivu.
  • Ensure speaker wires are not shorted.
  • Reduce bass boost settings.
• Bassi debuli:
  • Aumentà ampguadagnu di vita gradualmente.
  • Adjust low-pass filter frequency.
  • Verify correct polarity of speaker wiring.
  • Check enclosure for air leaks or improper volume.

7. Specificazioni

8. Garanzia è Support

The MTX Audio 5512-22 Subwoofer comes with a Garanzia limitata di 2 anniPer piacè cunservate a vostra prova d'acquistu per e richieste di garanzia.

For technical assistance or further inquiries, please contact MTX Audio Tech Support at 800.225.5689.