NVX XFLOC4 4-Channel Line Output Converter Instruction Manual

1. Introduzione

The NVX XFLOC4 is a 4-channel adjustable line output converter designed to integrate aftermarket amplifiers with factory car audio systems. This device converts high-level speaker signals from your vehicle's factory stereo into low-level RCA signals, which are required by most aftermarket amplifiers.

It features an integrated digital noise filter to ensure clear audio reproduction and a DC amplifier turn-on trigger for convenient system activation. This manual provides detailed instructions for the proper installation, operation, and maintenance of your NVX XFLOC4 to ensure optimal performance and longevity.

2. Funzioni chjave

• 4-Channel Conversion: Converts speaker-level signals to RCA line-level signals for up to four channels.
• Integrated Digital Noise Filter: Reduces unwanted interference for enhanced sound clarity.
• Adjustable 3:1 Step-Down Output: Allows precise tuning of output levels (up to 160W maximum input).
• DC Amplifier Turn-On Trigger: Provides a remote turn-on signal for external amplifiers.
• Low Distortion Design: Engineered for clear, high-quality sound reproduction.

3. Setup è Installazione

Proper installation is crucial for the performance of your NVX XFLOC4. If you are unsure about any steps, it is recommended to consult a professional car audio installer.

3.1 Cuntenuti di u pacchettu

• NVX XFLOC4 4-Channel Line Output Converter
• Wiring Harness (integrated)

3.2 Schema di cablaggio sopraview

The XFLOC4 connects to your factory speaker wires and provides RCA outputs to your aftermarket amplifier. It also generates a remote turn-on signal for the amppiù vivu.

Image 1: NVX XFLOC4 unit with integrated wiring harness and RCA outputs. The unit features adjustment screws for each channel.

3.3 Passi di cunnessione

1. Disconnect Vehicle Battery: Before starting any wiring, disconnect the negative terminal of your vehicle's battery to prevent electrical shorts.
2. Identificà i fili di l'altoparlanti: Locate the speaker wires from your factory stereo or amplifier. You will need to identify the positive (+) and negative (-) wires for each of the four channels (Front Left, Front Right, Rear Left, Rear Right). Refer to your vehicle's service manual or a reliable wiring diagram for accurate identification.
3. Connect Speaker Inputs: Connect the corresponding speaker wires from your vehicle to the input wires of the XFLOC4's harness. Ensure correct polarity (positive to positive, negative to negative).
   • Typically, solid colors are positive, and striped colors are negative, but this can vary. Always verify.
4. Cunnette l'alimentazione è a terra:
   • Cunnette u + 12V (Rossu) wire from the XFLOC4 harness to a switched +12V power source in your vehicle.
   • Cunnette u Terra (Nera) wire from the XFLOC4 harness to a solid chassis ground point. Ensure a clean, secure connection.
5. Connect Remote Turn-On Output: Cunnette u Remote (Blue) wire from the XFLOC4 harness to the remote turn-on input of your aftermarket amplifier. The XFLOC4 will generate a turn-on signal for your amplifier when it detects an audio signal.
6. Cunnette l'uscite RCA: Connect the RCA output cables from the XFLOC4 to the corresponding RCA inputs on your aftermarket amplifier (e.g., Front Left RCA to Front Left input on amp, etc.).
7. Cablaggio sicuru: Ensure all connections are secure and properly insulated using wire nuts, electrical tape, or heat shrink tubing. Route wires away from moving parts and heat sources.
8. Mount the XFLOC4: Mount the XFLOC4 unit in a secure, dry location, away from excessive heat or moisture.
9. Ricollegate a batteria: Once all connections are verified, reconnect the negative terminal of your vehicle's battery.

4. Operating Instructions

After successful installation, the NVX XFLOC4 requires minimal operation. The primary adjustment is setting the output level to match your amplifier's input sensitivity.

4.1 Adjusting Output Levels

The XFLOC4 features individual adjustment potentiometers (small screws) for each channel (Left, Right, Rear Left, Rear Right) on the unit. These allow you to fine-tune the signal level sent to your amppiù vivu.

1. Start with the adjustment screws turned fully counter-clockwise (minimum output).
2. Turn on your car audio system and play a familiar piece of music at a moderate volume.
3. Slowly turn the adjustment screws clockwise for each channel until you achieve a clean, undistorted sound from your amplifier. Avoid turning them up too high, as this can introduce distortion.
4. Aghjustate u vostru amplifier's gain settings according to its manufacturer's instructions, ensuring that the amplifier is not clipping (distorting). The XFLOC4's output should be set to provide a strong, clean signal to the amplifier without overdriving it.

The integrated digital noise filter operates automatically to minimize interference, contributing to the overall clarity of your audio system.

5. Mantenimentu

The NVX XFLOC4 is designed for reliable, long-term operation with minimal maintenance.

• Ispezione periodica: Verificate periodicamente tutti i cunnessione di i fili per assicurassi ch'elli sianu sicuri è senza corrosione.
• Pulizia: If necessary, gently wipe the exterior of the unit with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
• Prutezzione di l'ambiente: Ensure the unit remains in a dry environment, protected from extreme temperatures and direct sunlight.

6. Risoluzione di prublemi

If you experience issues with your NVX XFLOC4, refer to the following troubleshooting guide.

6.1 Problemi cumuni è Soluzioni

7. Specificazioni

8. Garanzia è Support

For information regarding the warranty coverage for your NVX XFLOC4, please refer to the warranty card included with your product or visit the official NVX websitu. I termini è e cundizioni di garanzia ponu varià secondu a regione è u rivenditore.

If you require technical assistance or have questions not covered in this manual, please contact NVX customer support through their official websitu o u rivenditore da quale avete acquistatu u pruduttu.