QIACHIP WL101 Receiver and WL102 Transmitter 433MHz RF Wireless Module Kit Instruction Manual

Introduzione

This manual provides detailed instructions for the QIACHIP WL101 Superheterodyne Receiver and WL102 Transmitter 433MHz RF Wireless Module Kit. This kit is designed for various DIY projects, including remote control applications with platforms like Arduino UNO. It operates on the 433MHz frequency band and supports ASK/OOK modulation.

Cuntenutu di u pacchettu:

• 1 x WL101 Superheterodyne Receiver Module
• 1 x WL102 Transmitter Module
• 2 x Antennas (for receiver and transmitter)

Informazioni di sicurezza

Handle batteries with care. Avoid extreme temperatures. Do not interfere with other wireless devices.

Funzioni di u produttu

• Frequenza: 433 MHz RF
• Modu di modulazione: Supports ASK/OOK modulation
• Potenza di trasmissione: Greater than 11dBm (for WL102 Transmitter)
• Tipu di ricevitore: Superheterodyne (for WL101 Receiver)
• Applicazione: Suitable for motorcycles, automobile anti-theft products, home security systems, electric doors, remote control sockets, LED lighting, garage door openers, and various remote control applications.

Specificazioni

WL101 Receiver Module

• Mudellu: WL101
• Voltage: Typically 3.3V - 5V (refer to specific datasheet for exact range)
• Corrente di funziunamentu: Bassu cunsumu d'energia
• Frequenza: 433 MHz
• Dimensioni: Approximately 1.18 inches x 0.35 inches (30mm x 9mm)

Descrizzione di l'imagine: A green circuit board showing the WL101 receiver module with dimensions indicated. The length is approximately 1.18 inches and the width is 0.35 inches.

WL102 Transmitter Module

• Mudellu: WL102
• Voltage: Typically 3.3V - 12V (refer to specific datasheet for exact range)
• Corrente di funziunamentu: Varies with transmit power
• Frequenza: 433 MHz
• Potenza di trasmissione: > 11 dBm
• Dimensioni: Circa 13mm x 13mm

Descrizzione di l'imagine: A small blue circuit board showing the WL102 transmitter module with a ruler indicating its size, approximately 13 mm.

Pinout and Connections

WL101 Superheterodyne Receiver Pinout

The WL101 receiver module features six pins for power, ground, data output, and antenna connection. Refer to the diagram below for pin identification.

Descrizzione di l'imagine: A green circuit board showing the WL101 receiver module. Six pins are labeled 1 through 6. Pin 1 is ANT (Antenna), Pin 2 is GND (Power ground), Pin 3 is VIN(VDD) (Power input), Pin 4 is DO(DATA) (Data output), Pin 5 is DO(DATA) (Data output), and Pin 6 is GND (Power ground).

WL102 Transmitter Pinout

The WL102 transmitter module has pins for power, ground, data input, and antenna. Note that the EN (Enable) pin is internally connected to the power supply and has no external function.

Descrizzione di l'imagine: A small green circuit board showing the WL102 transmitter module. It has four pins at the bottom. The text indicates 'DAT - Wave signal input', 'OUT - Antenna pin', 'EN - Enable Pin (connected to power supply, no function)', '-' Power ground Pin, '+' Power supply pin.

Example Connection to Arduino UNO (WL101 Receiver)

This diagram illustrates a typical connection of the WL101 receiver module to an Arduino UNO board. Ensure correct voltage and data pin connections.

Descrizzione di l'imagine: A circuit diagram showing a QIACHIP WL101-341 Superheterodyne 433MHz Receiver connected to an Arduino UNO board. The receiver's VDD pin is connected to Arduino's 5V, GND to GND, and one of the DO(DATA) pins to a digital input pin (e.g., D2) on the Arduino. The antenna is shown connected to the ANT pin.

Istituisci

Cunnessione antenna

For optimal performance, connect the supplied helical antenna to the ANT pin of the WL101 receiver and the OUT pin of the WL102 transmitter. The length of the antenna is critical for 433MHz operation; a quarter-wavelength antenna (approximately 17.3 cm or 6.8 inches for 433MHz) is recommended for best range, though the provided coiled antennas are suitable for shorter distances.

Alimentazione elettrica

• WL101 Receiver: Connect the VIN(VDD) pin to a stable power source (e.g., 5V from Arduino) and GND to ground.
• WL102 Transmitter: Connect the '+' pin to a stable power source (e.g., 3.3V to 12V, depending on desired range and power) and '-' to ground.

Cunnessione di dati

• WL101 Receiver: Connect one of the DO(DATA) pins to a digital input pin on your microcontroller (e.g., Arduino).
• WL102 Transmitter: Connect the DAT pin to a digital output pin on your microcontroller.

Istruzzioni di funziunamentu

Principiu di Operazione Basica

The WL102 transmitter sends data using Amplitude Shift Keying (ASK) or On-Off Keying (OOK) modulation at 433MHz. The WL101 superheterodyne receiver is designed to efficiently detect and demodulate these signals.

Microcontroller Programming (e.g., Arduino)

1. Transmitter (WL102): Program your microcontroller to send digital data (e.g., ON/OFF pulses) to the DAT pin of the WL102. Libraries like "RCSwitch" or "VirtualWire" are commonly used for encoding and transmitting data.
2. Receiver (WL101): Program your microcontroller to read digital data from the DO(DATA) pin of the WL101. The same libraries (e.g., "RCSwitch", "VirtualWire") can be used to decode the received signals.
3. Prutucollu di dati: Ensure that the data encoding and decoding protocols used by the transmitter and receiver microcontrollers are compatible.

Considerazioni di gamma

The effective range of the modules depends on several factors, including antenna quality, power supply voltage (for transmitter), environmental interference, and line of sight. Optimal antenna tuning and clear line of sight will maximize range.

Mantenimentu

• Mantene asciuttu: Protect the modules from moisture and humidity to prevent corrosion and damage.
• Cunnessioni pulite: Ensure all pin connections are clean and secure.
• Evite u stress fisicu: Handle the modules carefully to prevent bending pins or damaging components.
• Cura di l'antenna: Ensure antennas are not bent or damaged, as this can significantly impact performance.

Risoluzione di prublemi

• Nisuna ricezione di signale:
  • Verify power connections to both modules.
  • Check antenna connections and ensure they are properly sized for 433MHz.
  • Confirm that the transmitter and receiver are operating on the same frequency (433MHz).
  • Ensure the data encoding/decoding libraries and protocols are correctly implemented.
  • Reduce distance between modules and check for obstructions or sources of interference.
• Corta gamma:
  • Improve antenna quality (e.g., use a proper quarter-wavelength wire antenna).
  • Increase transmitter power supply voltage (within specified limits).
  • Minimize environmental interference (e.g., other 433MHz devices, Wi-Fi routers).
  • Assicuratevi una linea di vista chjara trà u trasmettitore è u ricevitore.
• Operazione intermittente:
  • Check for loose connections or cold solder joints.
  • Ensure stable power supply to both modules.
  • Consider adding decoupling capacitors near power pins if experiencing noise issues.
• Module Appears Damaged:
  • Inspect for visible signs of corrosion or physical damage. If found, replacement may be necessary.

Garanzia è Supportu

QIACHIP products are designed for reliability. For technical support or inquiries regarding your WL101/WL102 module kit, please refer to the seller's support channels or the QIACHIP official websitu. I dettagli specifichi di a garanzia ponu varià secondu a regione è u rivenditore.