1. Produttu Finituview
The Eberle KLR-E 7010 is a bimetal thermostat designed for controlling fancoil units. It provides precise temperature regulation and offers control over fan speed and operating mode (heating or cooling). This manual provides essential information for the safe and efficient installation, operation, and maintenance of your thermostat.
Figura 1: Fronte view of the Eberle KLR-E 7010 Fancoil Thermostat. The image displays the front panel of the thermostat, which is white with the 'EBERLE' brand name in the top left. On the right side, there is a large rotary dial for temperature setting, marked in degrees Celsius from 5 to 30. An arrow indicates the current setpoint. On the left, there are two horizontal slide switches. The top switch controls the fan speed, with icons representing different fan speeds. The bottom switch selects between heating (wavy lines), off (center), and cooling (snowflake) modes.
2. Importanti Instructions Safety
- Always disconnect power to the fancoil unit and thermostat at the main circuit breaker before performing any installation, wiring, or maintenance.
- L'installazione è u cablaggio devenu esse effettuati da un elettricista qualificatu in cunfurmità cù tutti i codici elettrici lucali è naziunali.
- Do not operate the thermostat with wet hands or when standing on a wet surface.
- Assicuratevi chì tutti i fili elettrici sianu sicuri è ben isolati per prevene i periculi elettrichi.
- This device is designed for indoor use only. Do not expose it to moisture, extreme temperatures, or direct sunlight.
- Keep the thermostat away from children and pets.
3. Guida d'installazione
3.1. Cuntenutu di u pacchettu
Verificate chì tutti i cumpunenti sò presenti prima di principià l'installazione:
- Eberle KLR-E 7010 Fancoil Thermostat unit
- Mounting screws (typically included with the unit)
- Manuale di istruzioni (questu documentu)
3.2. Istruzzioni di Montaggio
- Sceglie u locu: Choose an interior wall location, approximately 1.5 meters (5 feet) above the floor, away from direct sunlight, drafts, heat sources, or areas with poor air circulation.
- Disconnect Power: Turn off the power to the fancoil unit at the main circuit breaker. Verify that power is off using a voltagè testatore.
- Piastra di basa separata: Separate cù cura u coperchiu frontale di u termostatu da a so piastra di basa.
- Piastra di basa di muntatura: Position the base plate on the wall and mark the drilling locations. Drill holes and insert wall anchors if necessary. Secure the base plate to the wall using the provided mounting screws.
- cablaggio: Refer to the wiring diagram (Section 3.3) and connect the electrical wires to the appropriate terminals on the base plate. Ensure all connections are tight and correct.
- Attaccate a copertina frontale: Once wiring is complete and verified, carefully reattach the front cover to the base plate, ensuring it clicks securely into place.
- Ripristina l'energia: Riavvitate a corrente à l'interruttore principale.
3.3. Schema di Cablaggio
The Eberle KLR-E 7010 thermostat is designed for 230 Volts systems. Due to variations in fancoil unit configurations and local electrical codes, a generic wiring diagram cannot be provided here. It is imperative that a qualified electrician performs all wiring to ensure proper functionality and safety. The electrician should consult the specific wiring instructions provided with your fancoil unit and the terminal markings on the thermostat's base plate.
4. Operating Instructions
4.1. Controls Overview
The thermostat features three primary controls:
- Dial di temperatura: A large rotary dial on the right side of the unit, marked in degrees Celsius, used to set the desired room temperature.
- Interruttore di velocità di u ventilatore: A horizontal slide switch on the upper left, typically with three fan blade icons, allowing selection of low, medium, or high fan speed.
- Mode Selection Switch: A horizontal slide switch on the lower left, used to select between heating (wavy lines), cooling (snowflake), or off (center) modes.
4.2. Setting Temperature
To set the desired room temperature, rotate the large dial clockwise or counter-clockwise until the indicator arrow points to your preferred temperature in degrees Celsius. The thermostat will then work to maintain this temperature.
4.3. Fan Speed Control
Use the upper left slide switch to adjust the fancoil's fan speed:
- Bassu: For quiet operation and minimal air circulation.
- Medium: A balanced setting for general comfort.
- Altu: For rapid temperature change or maximum air circulation.
4.4. Mode Selection (Heating/Cooling)
Use the lower left slide switch to select the operating mode:
- Heating (wavy lines): The thermostat will activate the heating function when the room temperature falls below the setpoint.
- Off (posizione centrale): The fancoil unit will remain off, regardless of temperature.
- Cooling (snowflake): The thermostat will activate the cooling function when the room temperature rises above the setpoint.
5. Mantenimentu
The Eberle KLR-E 7010 thermostat requires minimal maintenance.
- Pulizia: Periodically wipe the exterior of the thermostat with a soft, dry cloth to remove dust. Do not use abrasive cleaners, solvents, or spray directly onto the unit.
- Nisuna parte riparabile da l'utilizatori: The thermostat contains no user-serviceable parts. Do not attempt to open or repair the unit yourself. Refer all servicing to qualified personnel.
6. Risoluzione di prublemi
If you experience issues with your Eberle KLR-E 7010 thermostat, consult the table below for common problems and potential solutions.
| Prublemu | Causa Possibile | Soluzione |
|---|---|---|
| Thermostat not responding / No power | No power at the circuit breaker; Loose wiring connection. | Check the circuit breaker and ensure it is in the 'ON' position. Verify all wiring connections are secure (consult a qualified electrician). |
| Fancoil not heating/cooling | Incorrect mode selected; Temperature setpoint too high/low; Fancoil unit malfunction. | Ensure the mode switch is set to 'Heating' or 'Cooling' as desired. Adjust the temperature setpoint appropriately. Check the fancoil unit for operational issues. |
| Fan ùn funziona micca | Fan speed switch set to 'Off' (if applicable); Fancoil unit fan malfunction. | Ensure the fan speed switch is set to a desired speed (Low, Medium, or High). Check the fancoil unit's fan for issues. |
| Lettura di temperatura imprecisa | Thermostat located near heat/cold source or draft. | Relocate the thermostat to a more suitable position if possible, away from direct influences. |
If the problem persists after attempting these solutions, contact a qualified technician or customer support.
7. Specifiche tecniche
- Marca: Eberle
- Mudellu: KLR-E 7010
- Tipu: Bimetal Fancoil Thermostat
- Voltage: 230 Volts
- Dimensioni (L x W x H): 11.71 x 7.11 x 2.69 cm (circa 4.61 x 2.80 x 1.06 pollici)
- Pesu: 120 grammi (circa 0.26 libbre)
- Controlu di u fan: 3-speed fan selector
- Modu cuntrollu: Heating/Cooling/Off selector
- Gamma di temperatura: Typically 5°C to 30°C (41°F to 86°F)
- Batterie: Micca ubligatoriu, micca inclusu
- Riferimentu di u fabricatore: 3024146
- Numeru di mudellu di l'articulu: 8402414979620
8. Garanzia infurmazione
This Eberle KLR-E 7010 thermostat is covered by the manufacturer's standard warranty. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the documentation provided at the time of purchase or contact your retailer.
9. Assistenza Clienti
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the retailer from whom you purchased the product or visit the official Eberle website for support contact information. When contacting support, please have your product model (KLR-E 7010) and proof of purchase readily available.
