Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge Instruction Manual

1. Produttu Finituview

The Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge (Model 69ELF114TWG) is designed to reduce incoming water pressure to a safe and consistent level for residential and commercial plumbing systems. This unit features a compact design, lead-free bronze construction, and an integrated internal bypass mechanism. It includes a color-coded gauge for easy pressure monitoring and adjustment.

Figure 1: Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge. This image shows the regulator with its integrated pressure gauge and yellow adjustment handle.

2. Informazioni di sicurezza

• Always shut off the main water supply before beginning any installation or maintenance.
• Portate l'equipaggiu di prutezzione individuale (PPE) adattatu, cum'è l'occhiali di sicurezza è i guanti.
• Assicuratevi chì tutti i raccordi sianu sigillati currettamente per impedisce perdite.
• Consult local plumbing codes and regulations for proper installation procedures.
• Sè vo avete qualchì dubbitu nantu à qualchì parte di l'installazione, cunsultate un idraulicu qualificatu.

3. Cuntenutu di u pacchettu

Verificate chì tutti i cumpunenti sò presenti prima di principià l'installazione:

• 1x Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator
• 1x Integrated Pressure Gauge

4. Installazione

This regulator features a double union PEX-A (cold expansion) barb design for simplified installation in PEX-A piping systems. Ensure the regulator is installed in the correct flow direction, indicated by an arrow on the body.

1. Preparate u situ di stallazione: Turn off the main water supply. Drain the water lines to relieve pressure. Select a suitable location for the regulator, typically after the main shut-off valve and before any branch lines.
2. Cut and Prepare PEX-A Piping: Cut the PEX-A pipe to the required length, ensuring clean, square cuts. Prepare the pipe ends for cold expansion connections according to PEX-A system manufacturer guidelines.
3. Connect the Regulator:
   • Apply appropriate thread sealant (e.g., Teflon tape or pipe dope) to the male threads of the PEX-A fittings.
   • Thread the PEX-A fittings onto the double union ends of the regulator. Ensure the flow arrow on the regulator body points in the direction of water flow into the building.
   • Tighten the union nuts securely, but do not overtighten.
   • Perform cold expansion connections on the PEX-A pipe ends to the fittings according to PEX-A system manufacturer instructions.
4. Installa un manometru di pressione: The pressure gauge is typically pre-installed. Ensure it is securely threaded into the designated port on the regulator body.
5. Restore Water Supply and Check for Leaks: Slowly turn on the main water supply. Carefully inspect all connections for any signs of leaks. Tighten connections as necessary.

Figura 2: Side view of the Apollo Water Pressure Regulator, showing the double union PEX-A connections and the flow direction arrow. Note the "MAX INLET 400 PSI" marking.

5. Operating Instructions

The regulator is factory-set at 50 psi and is adjustable from 15 psi to 75 psi. No special tools are required for adjustment.

1. Verificate a pressione attuale: Observe the reading on the integrated pressure gauge. The gauge is color-coded to indicate pressure ranges (e.g., Low, Optimal, Excessive).
2. Ajuste di pressione:
   • À cresce pressure: Turn the yellow adjustment handle in senso orario.
   • À diminuite pressure: Turn the yellow adjustment handle in sensu antiurariu.
   • Make small adjustments and allow the system pressure to stabilize before re-checking the gauge.
3. Cunfirmà l'impostazione: Once the desired pressure is achieved (typically between 50-60 psi for most residential applications), confirm the reading on the gauge.

Figura 3: Primu pianu view of the Apollo Water Pressure Regulator, highlighting the pressure gauge with its color-coded optimal range and the yellow adjustment handle.

6. Mantenimentu

The Apollo Water Pressure Regulator is designed for minimal maintenance. Regular checks can help ensure optimal performance.

• Periodic Pressure Check: Periodically check the pressure gauge to ensure the system pressure remains at the desired setting. Fluctuations may indicate a need for adjustment or inspection.
• Ispezione di perdite: Annually inspect the regulator and connections for any signs of leaks or corrosion.
• Pulizia: Clean the exterior of the regulator with a damp cloth as needed. Do not use harsh chemicals.
• Sediment Filter (Optional): If your water supply contains significant sediment, consider installing a sediment filter upstream of the pressure regulator to prevent internal clogging.

7. Risoluzione di prublemi

8. Specificazioni

• Mudellu: 69ELF114TWG
• Materiale: Bronzu
• Dimensione di cunnessione di l'ingressu: 3/4 Inch
• Tipu di cunnessione d'ingressu: Cross Linked Polyethylene (PEX-A)
• Tipu di cunnessione di presa: PEX
• Pressione operativa massima: 400 PSI (Inlet)
• Gamma di pressione regulabile: 15 - 75 PSI (Factory-set at 50 PSI)
• Dimensioni di l'articulu (L x W x H): 2.13 x 7 x 8 inch
• Pesu di l'articulu: 2.53 liri
• Certificazioni: Certified to ASSE 1003 and CSA B356, listed by ASSE and IAPMO (cUPC)
• Funzioni speciali: Integrated internal bypass mechanism, Color-coded gauge

9. Garanzia è Support

This Apollo Water Pressure Regulator comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Apollo customer support.

For technical support or inquiries, please visit the official Apollo websitu o cuntattate u so dipartimentu di serviziu di u cliente.