Pro-Ject Debut RecordMaster II Turntable with USB (OM5e)

1. Introduzione

The Pro-Ject Debut RecordMaster II is a high-fidelity turntable designed for an enhanced vinyl listening experience and digital conversion. This model features a pre-mounted OM5e cartridge, a built-in switchable phono preamplifier, and a USB output for direct connection to a PC or Mac. It incorporates a belt drive system with a low-noise AC motor, TPE decoupling, and a DC-driven AC generator for stable speed. Electronic speed change allows for playback at 33, 45, and 78 RPM, with a simple stylus exchange (OM78, not included) and drive belt adjustment required for 78 RPM.

This manual provides essential information for the proper setup, operation, and maintenance of your turntable to ensure optimal performance and longevity.

2. Istruzzioni di sicurità

• Leghjite attentamente tutte l'istruzzioni prima di l'usu.
• Keep the turntable away from water, moisture, and direct sunlight.
• Do not place the turntable near heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Aduprate solu accessori / accessori specificati da u fabricatore.
• Scollegate u giradischi durante i temporali o quandu ùn hè micca adupratu per longhi periodi.
• Riferite tutte l'assistenza à u persunale di serviziu qualificatu.
• Assicuratevi una ventilazione curretta intornu à l'unità.

3. Cuntenutu di u pacchettu

Verificate chì tutti l'articuli elencati quì sottu sò inclusi in u vostru pacchettu:

• Pro-Ject Debut RecordMaster II Turntable with pre-mounted OM5e cartridge
• Connect it RCA Cable
• Dustcover
• Adapter for 7-inch singles
• Alimentazione elettrica

4. Setup Guide

Follow these steps to set up your Pro-Ject Debut RecordMaster II turntable:

4.1 Unpacking and Placement

Carefully remove all components from the packaging. Place the turntable on a stable, level surface away from vibrations and direct heat sources. Ensure adequate space for the dustcover to open fully.

Figura 1: Da cima à fondu view of the Pro-Ject Debut RecordMaster II Turntable.

4.2 Installazione di u piattu è di a cintura

1. Pone u piattu nantu à u fusu.
2. Carefully loop the drive belt around the motor pulley and the inner rim of the platter.

4.3 Equilibriu di u bracciu è forza di tracciamentu

The turntable comes with a pre-mounted OM5e cartridge. Refer to the cartridge manufacturer's instructions for precise tracking force and anti-skating settings. Generally, balance the tonearm until it floats freely, then set the tracking force using the counterweight.

Figure 2: Close-up of the tonearm, showing the Pro-Ject branding.

4.4 Cunnessione à un sistema audio

The Debut RecordMaster II features a built-in switchable phono preamplifier and USB output. You can connect it to a line-level input on your hi-fi system or directly to a PC/Mac via USB.

• Cunnessione RCA: Use the supplied RCA cable to connect the turntable's output to an available line-level input (e.g., AUX, CD) on your amplifier or receiver. Ensure the phono preamplifier switch on the turntable is set to 'Line Out' if connecting to a line-level input, or 'Phono Out' if connecting to an amplificatore cù una entrata phono dedicata.
• Cunnessione USB: Connect the turntable to your computer using a USB cable (not included). This allows for digital recording of your vinyl.

Figure 3: Turntable integrated into a home audio setup with speakers.

Figure 4: Turntable connected to a laptop, demonstrating USB recording capability.

4.5 Dustcover Installation

Attach the dustcover hinges to the designated slots on the rear of the turntable. The dustcover protects the turntable from dust and debris when not in use.

5. Operating Instructions

5.1 Accensione / spegnimentu

Locate the power switch, typically on the underside or rear of the plinth. Turn the switch to the 'On' position to power the turntable. Turn it 'Off' when not in use.

Figure 5: Detail of the power switch for the turntable.

5.2 Selezzione di velocità

The turntable supports 33, 45, and 78 RPM playback. Use the electronic speed change function to select the appropriate speed for your record. For 78 RPM records, a specific OM78 stylus (not included) and a drive belt turnover to a larger diameter of the pulley are required.

5.3 Riproduzione di un discu

1. Mettite un discu nantu à u platu.
2. Ensure the correct playback speed is selected.
3. Raise the tonearm using the tonearm lift lever.
4. Movite delicatamente u bracciu sopra u solcu iniziale desideratu di u discu.
5. Slowly lower the tonearm using the lift lever. The stylus will descend onto the record and playback will begin.

5.4 Fermà a riproduzione

1. Raise the tonearm using the tonearm lift lever.
2. Move the tonearm back to its rest position.
3. Lower the tonearm onto its rest using the lift lever.
4. Turn off the turntable.

5.5 Registrazione USB

To record vinyl to your PC/Mac, connect the turntable via USB. Use appropriate audio recording software (not included) on your computer to capture the audio signal. Ensure the turntable's phono preamplifier is set to 'Line Out' for USB recording.

6. Mantenimentu

6.1 Pulizia di u Stilu

Regularly clean the stylus using a soft brush or a dedicated stylus cleaning fluid. Brush gently from back to front to remove dust and debris.

6.2 Registri di pulizia

Use a carbon fiber brush or a record cleaning solution to keep your vinyl records free of dust and static. Clean records before each play to minimize wear on the stylus and improve sound quality.

6.3 Dustcover Care

Clean the dustcover with a soft, damp tela. Evite i pulitori abrasivi chì ponu graffià a superficia.

7. Risoluzione di prublemi

If you encounter issues with your turntable, consult the following common problems and solutions:

8. Specificazioni

9. Garanzia è Support

For detailed warranty information, please refer to the documentation included with your product or visit the official Pro-Ject Audio Systems website. For technical support or service inquiries, please contact Pro-Ject customer service through their official channels.