1. Introduzione
This manual provides comprehensive instructions for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters. These transmitters are designed to be used with a compatible 12V 1-channel wireless receiver (receiver not included) to control various electronic devices remotely. Please read this manual carefully before use to ensure proper setup and operation.
Image 1.1: Three QIACHIP EV1527 Rf433m Wireless Remote Transmitters. Each remote features two buttons, labeled 'A' and 'B', and an attached metal keychain clip.
2. Produttu Finituview
The QIACHIP EV1527 Rf433m Wireless Remote Transmitter is a compact and ergonomic device designed for convenient remote control. Each remote features two silicone buttons and an indicator light.
2.1 Cumpunenti
- Silicone Buttons (A and B): Used to send control signals to the paired receiver.
- Indicatore luminoso: Illuminates when a button is pressed, indicating signal transmission.
- Chrome Bezel: Provides a durable and aesthetic finish.
- Metal Keychain: Allows for easy attachment to keys or other items.
Image 2.1: Diagram illustrating the key components of the remote control, including the silicone buttons (A and B), indicator light, chrome bezel, and metal keychain.
2.2 Gamma operativa
These remote transmitters offer a wide operating range, typically up to 100 meters in an open, unobstructed area. Actual range may vary depending on environmental factors and obstacles.
Image 2.2: Illustration depicting the effective operating range of the wireless remote, showing a signal reaching up to 100 meters in an open environment.
3. Setup
3.1 Installazione di batterie
The remote control requires one CR2032 button cell battery. The battery is typically pre-installed, but if replacement is needed or if the remote is not functioning, follow these steps:
- Aprite cù cura u telecomandu casing. This usually involves prying apart the two halves of the remote, often near the keychain loop.
- Locate the battery compartment on the circuit board.
- Eliminate a vechja batteria CR2032, nutendu a so polarità.
- Inserite una nova batteria CR2032 cù u latu pusitivu (+) rivoltu in sopra.
- Chjude u telecomandu casing in modu sicuru.
Image 3.1: View of the remote's internal circuit board, showing the placement of the CR2032 button cell battery.
3.2 Pairing with a Receiver
These transmitters are designed to work with a compatible QIACHIP 12V 1-channel wireless receiver (not included). A single receiver can pair with up to 20 remotes. The pairing process typically involves the following steps, though specific details may vary based on your receiver model:
- Power On Receiver: Ensure your 12V 1-channel wireless receiver is powered on.
- Clear Existing Programming (Recommended): To prevent conflicts, it is often recommended to clear any previous pairings on the receiver. This is typically done by pressing the receiver's learning button (often a small button on the circuit board) 8 times. The receiver's indicator light should flash rapidly and then turn off, confirming the memory has been cleared.
- Entra in u Modu di Apprendimentu: Press the receiver's learning button once or twice, depending on the desired operating mode (e.g., momentary, toggle, latched). The receiver's indicator light will illuminate steadily, indicating it is in learning mode.
- Transmit Signal: While the receiver's indicator light is steady, press the desired button (A or B) on your QIACHIP remote transmitter. The remote's indicator light will flash.
- Cunfirmà l'accoppiamentu: The receiver's indicator light should flash a few times and then turn off, confirming successful pairing.
- Funzionalità di prova: Press the paired button on the remote to ensure the receiver responds as expected.
Nota: Refer to your specific receiver's instruction manual for precise pairing procedures and mode selection (e.g., momentary, toggle, latched).
4. Uperativu
Once your QIACHIP EV1527 remote transmitter is successfully paired with a compatible receiver, operation is straightforward:
- Press Button A or B: Simply press the 'A' or 'B' button on the remote to send a signal to the receiver.
- Indicatore luminoso: The small indicator light on the remote will illuminate briefly when a button is pressed, confirming that a signal is being transmitted.
- Receiver Response: The paired receiver will execute the programmed action (e.g., turn a device on/off, open/close a garage door) according to its configured mode (momentary, toggle, or latched).
5. Mantenimentu
5.1 Sustituzione di batterie
If the remote's indicator light becomes dim or fails to illuminate, or if the remote's range decreases significantly, it may be time to replace the battery. The remote uses one CR2032 button cell battery.
- Open the remote casing cum'è descrittu in a Sezione 3.1.
- Eliminate cù cura a vechja batteria CR2032.
- Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
- Chjude u telecomandu casing in modu sicuru.
Nota: In some rare cases, after battery replacement, the remote may need to be re-paired with the receiver. Follow the pairing instructions in Section 3.2 if necessary.
6. Risoluzione di prublemi
- A distanza ùn risponde micca:
- Check the battery: Ensure the CR2032 battery is correctly installed and has sufficient charge. Try replacing it with a new battery.
- Receiver Power: Verify that your 12V 1-channel wireless receiver is properly powered and functioning.
- Re-pairing: Attempt to re-pair the remote with the receiver following the steps in Section 3.2.
- Remote Reset: If a new remote or a remote after battery change is not pairing, try removing and reinserting the battery in the remote to perform a soft reset, then attempt pairing again.
- Limited Operating Range:
- Obstructions: Ensure there are no significant physical obstructions (e.g., thick walls, metal objects) between the remote and the receiver.
- Antenna: Verify that the receiver's antenna (if applicable) is fully extended and unobstructed.
- Interference: Minimize potential sources of radio frequency interference in the vicinity.
7. Specificazioni
| Feature | Detail |
|---|---|
| Numero di mudellu | KT05-AB-3 |
| Marca | QIACHIP |
| Frequency | 433MHz (Rf433m) |
| Encoding Chip | EV1527 |
| Tipu di batterie | 1 x CR2032 (required) |
| Max Supported Remotes (per receiver) | Finu à 20 |
| Gamma operativa | Finu à 100 metri (zona aperta) |
| Dispositivi compatibles | 12V 1-channel wireless receivers, Garage Door systems |
| Dimensioni di u pacchettu | 5.35 x 4.96 x 1.06 inch |
| Pesu di l'articulu | 3.53 once |
Image 7.1: Diagram showing the approximate dimensions of the remote control: 6.1 cm in length and 2.9 cm in width.
8. Garanzia è Support
8.1 Garanzia infurmazione
Specific warranty details for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters are not provided in the product documentation. For information regarding warranty coverage, please contact the seller or manufacturer directly.
8.2 Assistenza Clienti
For further assistance, technical support, or inquiries, please contact QIACHIP customer service through their official channels or the retailer where the product was purchased.
You can visit the QIACHIP Store for more information: QIACHIP Store on Amazon
