Introduzione
This manual provides essential information for the safe and efficient use of your HPE ProLiant DL380 G10 Plus 2U Rack Server. Please read this manual thoroughly before installation and operation, and retain it for future reference.
The HPE ProLiant DL380 G10 Plus is a versatile 2U rack server designed for demanding workloads, offering high performance and expandability. It features an Intel Xeon Gold 5315Y processor, 32 GB RAM (expandable to 2 TB), and a 12Gb/s SAS controller.
Informazioni di sicurezza
Osservate sempre e seguenti precauzioni di sicurezza per prevene ferite è danni à l'attrezzatura:
- Assicurà una messa à terra curretta per tutte e cunnessione elettriche.
- Do not operate the server with covers removed.
- Disconnect power before performing any maintenance or upgrades.
- Install the server in a well-ventilated area to prevent overheating.
- Use only HPE-approved components and accessories.
Guida di installazione
1. Unpacking è Inspection
Carefully remove the server from its packaging. Inspect for any signs of shipping damage. Report any damage to your carrier and reseller immediately.
Figura 1: Fronte view of the HPE ProLiant DL380 G10 Plus 2U Rack Server. This image shows the server's front panel, including drive bays and control buttons.
2. Installazione Rack
The HPE ProLiant DL380 G10 Plus is a 2U rack-mountable server. Follow the instructions provided with your rack rail kit for secure installation into a standard 19-inch server rack.
- Attach the rail kit to the server and the rack.
- Slide the server into the rack until it clicks into place.
- Secure the server to the rack using the provided screws.
3. Cunnessione di periferiche è alimentazione
Connect necessary peripherals such as keyboard, mouse, and monitor (if applicable) to the server's rear ports. Connect network cables to the appropriate Ethernet ports. Finally, connect the power cords to the server's power supply units and then to a grounded power outlet.
Istruzzioni di funziunamentu
1. Accensione iniziale
Press the power button on the front panel of the server. Observe the POST (Power-On Self-Test) sequence. The server will typically boot into the installed operating system or a pre-boot environment.
2. Accessing iLO (Integrated Lights-Out)
HPE iLO provides remote server management capabilities. To access iLO, connect a network cable to the iLO dedicated management port and configure its IP address through the server's BIOS/UEFI settings or via DHCP.
- apre a web browser and enter the iLO IP address.
- Log in using the credentials found on the iLO default password tag (usually on the server chassis).
3. Installazione di u Sistema Operativu
Refer to your operating system's documentation for detailed installation procedures. HPE provides drivers and firmware updates on its official support websitu.
Mantenimentu
1. Pulizia regulare
Periodically clean the server's exterior and ventilation openings to ensure optimal airflow. Use a soft, dry cloth. Do not use liquid cleaners directly on the server.
2. Aghjurnamenti di Firmware è Driver
Verificate regularmente l'assistenza HPE website for the latest firmware and driver updates for your DL380 G10 Plus server. Keeping components updated ensures stability, performance, and security.
3. Sustituzione di cumpunenti
For replacing components like hard drives, memory modules, or power supplies, always refer to the specific service manual for the HPE ProLiant DL380 G10 Plus. Ensure the server is powered off and disconnected from power before opening the chassis.
Risoluzione di prublemi
This section provides solutions to common issues. For more complex problems, consult the HPE support documentation or contact technical support.
| Prublemu | Causa Possibile | Soluzione |
|---|---|---|
| Server does not power on. | No power, faulty power supply, loose connection. | Check power cords, verify power outlet, test with another power supply if available. |
| System hangs during boot. | Faulty RAM, incorrect BIOS settings, corrupted OS. | Reseat RAM modules, reset BIOS to default, attempt OS repair or reinstallation. |
| Prublemi di cunnessione di rete. | Loose cable, incorrect network settings, faulty NIC. | Check network cables, verify IP configuration, update NIC drivers, test with a different port or NIC. |
Specificazioni
| Feature | Detail |
|---|---|
| Mudellu | HPE ProLiant DL380 G10 Plus |
| Part Number | P55248-B21 |
| Fattore di forma | Rack 2U |
| Processore | 1 x Intel Xeon Gold 5315Y 3.20 GHz (supports 2 processors) |
| Chipset | Intel C621A |
| Memoria | 32 GB RAM (expandable up to 2 TB) |
| Controller di Storage | 12Gb/s SAS Controller |
| Grafica | Up to 16 MB Graphic Card |
| Dimensioni di u pacchettu | 37.4 x 23.23 x 10.63 inch |
| Pesu di l'articulu | 56.1 liri |
| Socket CPU | LGA 1151 |
| Cache Secundaria | 16 MB |
Garanzia è Supportu
Your HPE ProLiant DL380 G10 Plus server is covered by a manufacturer's warranty. For detailed warranty terms and conditions, please refer to the documentation included with your purchase or visit the official HPE support websitu.
For technical assistance, product registration, or to download the latest drivers and firmware, please visit the Assistenza HPE websitu. You may also contact HPE technical support directly using the contact information provided on their websitu.
Nota: Protection plans may be available for extended coverage. Check with your reseller for options like the 4-Year Protection Plan or Complete Protect monthly plan.
