AXAGON ADSA-D25 SATA 2.5 Clone Dual SSD Dock Station - USB 3.2 Gen 1 User Manual

1. Introduzione

The AXAGON ADSA-D25 is a dual dock station designed for 2.5-inch SATA Solid State Drives (SSDs) and Hard Disk Drives (HDDs). It provides a convenient solution for connecting two SATA drives to a computer via USB 3.2 Gen 1 (USB 3.0) interface, offering data transfer speeds up to 5 Gbps. Additionally, it features an offline clone function, allowing direct duplication of one drive to another without requiring a computer connection.

2. Cuntenutu di u pacchettu

Verificate chì tutti l'articuli elencati quì sottu sò presenti in u vostru pacchettu:

• AXAGON ADSA-D25 Dual SSD/HDD Dock Station
• USB Micro-B to USB-A Cable
• Adattatore di putenza
• Manuale d'usu

Image: The ADSA-D25 dock station, showing the rear ports (USB Micro-B, power input), power button, clone button, and the included USB Micro-B to USB-A cable and power cable.

3. Produttu Finituview

The ADSA-D25 dock station is designed for ease of use and efficient data management. It supports two 2.5-inch SATA SSDs or HDDs simultaneously.

Image: Front view of the AXAGON ADSA-D25 dock station with two 2.5-inch SSDs inserted into the top slots, highlighting its dual drive capability.

Funzioni chjave:

• Dual 2.5" SATA Drive Support: Accommodates two 2.5-inch SATA I/II/III SSDs or HDDs.
• USB 3.2 Gen 1 Interface: Provides high-speed data transfer up to 5 Gbps.
• Funzione di clonazione offline: Allows direct drive-to-drive cloning without a computer.
• Supportu UASP: Enhances data transfer performance.
• Supportu TRIM: Optimizes SSD performance and longevity.
• SMART Support: Monitors drive health and status.
• Indicatori LED: Status and cloning progress indication.

Image: The ADSA-D25 dock station with graphical icons illustrating its main features: 5 Gbps USB 3.2 Gen 1 speed, support for two 2.5-inch SSDs/HDDs, and SSD/HDD duplication capability.

4. Setup

Follow these steps to set up your ADSA-D25 dock station:

1. Connect Power: Connect the provided power adapter to the DC 3.5mm power input port on the back of the dock station, then plug the adapter into a power outlet.
2. Inserisce unità: Gently insert your 2.5-inch SATA SSDs or HDDs into the top slots of the dock station. Ensure they are fully seated.
3. Connect to Computer (for Data Transfer): If you intend to use the dock for data transfer, connect the USB Micro-B end of the provided USB cable to the dock station and the USB-A end to an available USB 3.2 Gen 1 (USB 3.0) port on your computer.
4. Power On: Press the power button on the back of the dock station. The power LED indicator will illuminate.

5. Modi upirativu

5.1. Modu di trasferimentu di dati

In this mode, the dock station functions as an external drive enclosure, allowing you to access data on the inserted drives from your computer.

1. Ensure the dock station is powered on and connected to your computer via the USB cable.
2. Insert one or two 2.5-inch SATA SSDs/HDDs into the slots.
3. U vostru sistema operativu duveria rilevà automaticamente i dischi. Apparisceranu cum'è dispositivi di almacenamiento amovibili.
4. You can now access, read, and write data to the drives as you would with any other external storage.

Image: The ADSA-D25 dock station connected to a laptop, illustrating its use for data transfer with two SSDs inserted. The image also highlights the 5 Gbps USB 3.2 Gen 1 speed compared to 480 Mbps USB 2.0.

5.2. Funzione di clonazione offline

The offline clone function allows you to duplicate the contents of a source drive to a target drive without a computer connection. The target drive must be equal to or larger in capacity than the source drive.

Important: All data on the target drive will be erased during the cloning process. Back up any important data from the target drive before proceeding.

1. Ensure the dock station is powered off and disconnected from the computer.
2. Inserite u unità surghjente (l'unità da a quale vulete copià) in u Source (HDD1) slot.
3. Inserite u unità di destinazione (l'unità induve vulete copià) in u Target (HDD2) slot.
4. Connect the power adapter and power on the dock station.
5. Appughjà è tene premutu Clone buttone on the back of the dock station for approximately 3-5 seconds until the LED indicators begin to flash.
6. Release the Clone button. The cloning process will begin, and the progress will be indicated by the LEDs.
7. Once all LEDs are solid, the cloning process is complete.
8. Power off the dock station and safely remove the drives.

6. Indicatori LED

The ADSA-D25 features LED indicators to show power status, drive activity, and cloning progress.

• LED di putenza: S'illumina quandu u dispusitivu hè accesu.
• Drive Activity LEDs: Flash to indicate data access for each respective drive.
• Cloning Progress LEDs: During an offline clone, these LEDs indicate the percentage of completion (e.g., 25%, 50%, 75%, 100%).

Image: The ADSA-D25 dock station with its vertical LED strip, illustrating how different segments illuminate to show cloning progress (25%, 50%, 75%, 100%).

7. Mantenimentu

To ensure optimal performance and longevity of your ADSA-D25 dock station:

• Mantene l'apparechju in un ambiente pulitu è ​​asciuttu, luntanu da a luce diretta di u sole è da temperature estreme.
• Evite di abbandunà o sottumette u dispusitivu à forti impatti.
• Ùn pruvate micca di smuntà l'unità. Questu annullerà a garanzia.
• Pulite l'esternu cù un pannu dolce è asciuttu. Ùn aduprate micca detergenti liquidi.

8. Risoluzione di prublemi

8.1. Dispositivu micca rilevatu da l'urdinatore

• Ensure the dock station is powered on and the USB cable is securely connected to both the dock and the computer.
• Pruvate a cunnessione à un portu USB diversu in u vostru urdinatore.
• Pruvate cù un altru cavu USB s'ellu hè dispunibule.
• Verify that the inserted SSD/HDD is properly seated and functional.

8.2. Drives Not Appearing in My Computer/File Explorer

• For new drives, they may need to be initialized, partitioned, and formatted in Disk Management (Windows) or Disk Utility (macOS) before they can be used.
• Ensure the drives are properly inserted and the dock station is powered on.

8.3. Offline Clone Fails or Does Not Start

• Ensure the dock station is disconnected from the computer before starting the clone process.
• Verify that the target drive's capacity is equal to or larger than the source drive's capacity.
• Ensure both drives are properly inserted into their respective slots (Source in HDD1, Target in HDD2).
• Press and hold the Clone button for the required duration (3-5 seconds) until the LEDs flash.
• If the issue persists, try using different drives to rule out drive-specific problems.

9. Specificazioni

Image: The underside of the ADSA-D25 dock station, revealing internal components and highlighting supported technologies such as UASP, TRIM, SMART, and compatibility with any capacity drive.

10. Garanzia è Support

AXAGON products are designed and manufactured with high quality standards. For warranty information and technical support, please refer to the official AXAGON websitu o cuntattate u vostru rivenditore lucale. Cunservate a vostra prova d'acquistu per e richieste di garanzia.