Yaheetech 10x10 Pop-Up Canopy Tent with 17 Solar LED Lights & Top Vent Instruction Manual

Introduzione

This manual provides detailed instructions for the setup, operation, and maintenance of your Yaheetech 10x10 Pop-Up Canopy Tent. Designed for ease of use and durability, this canopy offers ample shade and features integrated solar LED lighting for evening use. Please read this manual thoroughly before assembly and use to ensure safe and optimal performance.

Importante infurmazione di sicurezza

ATTENZIONE:

• For optimal performance and safety, do not use this canopy in conditions of strong breeze, continuous light rain, heavy rain, or any other extreme weather scenarios.
• Always anchor the canopy to the ground when in use using the provided stakes, sandbags, and ropes.
• Assicuratevi chì tutti i meccanismi di bloccu sianu cumpletamente impegnati durante l'installazione per impedisce u crollu.
• Mantene i zitelli è l'animali domestici luntanu da u baldacchinu durante l'installazione è u smontaggio.
• Do not hang heavy objects from the canopy frame.
• Avoid using open flames or heating devices inside or near the canopy.

Lista di cumpunenti è pezzi

Before beginning assembly, ensure all parts are present and accounted for. Refer to the image below for a visual guide.

Figure 1: All included components for the Yaheetech 10x10 Pop-Up Canopy Tent.

• Pop-Up Canopy Frame (1)
• Canopy Fabric with 17 Solar LED Lights (1)
• Wheeled Carry Bag (1)
• Sandbags (4)
• Anchor Ropes (4)
• Ground Stakes (12)
• Solar Panel (integrated into canopy)
• Cuntrollu à distanza (1)

Istruzzioni di stallazione

Follow these steps for quick and easy assembly of your canopy tent. It is recommended that two people perform the setup for optimal ease and safety.

Passu 1: Disimballà è pusizziunà a cornice

1. Remove the canopy frame and fabric from the wheeled carry bag.
2. Pone u quadru piegatu in u locu di cunfigurazione desideratu.
3. With a partner, gently pull the frame outwards from opposite corners to partially expand it.

Figure 2: Quick and easy installation steps.

Step 2: Attach the Canopy Fabric and Solar Panel

4. Drape the canopy fabric over the partially expanded frame. Ensure the solar panel is positioned at the top center.
5. Locate the electrical connector from the solar panel and connect it to the corresponding port on the canopy fabric.
6. Secure the canopy fabric to the frame using the hook and loop fasteners located at each corner and along the frame.

Figure 3: Key features and attachment points of the canopy.

Step 3: Fully Extend the Frame and Adjust Height

7. From underneath the canopy, push up the horizontal bars at each corner until they "click" into place, fully extending the frame.
8. Adjust the canopy height by pushing the spring buttons on each leg and sliding the telescopic outer tubes along the legs. There are 3 adjustable height settings from 8.8' to 9.4'.
9. Impurtante: Do not overextend the frame legs beyond the designated height settings, as this may damage the canopy fabric or frame.

Passu 4: Assicurà u Canopy

9. Fill the four sandbags with sand or other heavy material and attach them to the canopy legs using the hook and loop fasteners.
10. Attach the anchor ropes to the corner rings of the canopy.
11. Drive the ground stakes into the ground at an angle, securing the anchor ropes to them. Ensure the ropes are taut to provide stability.

Istruzzioni di funziunamentu

Funzionamentu di e luci solari LED

Your canopy tent is equipped with 17 built-in solar LED lights for illumination during the evening. The lights are powered by the integrated solar panel or can be charged via a power bank (not included).

1. Carica iniziale: For first-time use, allow the solar panel to charge in direct sunlight for at least 6-8 hours to ensure sufficient power for the LED lights.
2. Control remoto: The LED lights are controlled by the included remote. The remote allows you to turn the lights ON/OFF and adjust brightness levels.
3. Batteria remota: The remote control requires a CR2025 button cell battery (included, usually with a pull tab to activate). Remove the plastic tab before first use.
4. Carica di u Power Bank: If solar charging is insufficient, you can connect a power bank (not included) to the USB port on the solar panel unit for alternative charging.

Figure 4: Day and Night view of the canopy with remote control for LED lights.

Figure 5: Two-way charging options for the solar LED lights.

Mantenimentu

• Pulizia: Pulite u tissutu di u baldacchinu cù acqua è sapone dolce. Ùn aduprate micca prudutti chimichi aggressivi o detergenti abrasivi. Lasciate asciugà cumpletamente à l'aria prima di almacenallu.
• Cura di u quadru: Inspect the steel frame regularly for any signs of rust or damage. Clean and dry any wet spots promptly.
• Conservazione: When not in use, disassemble the canopy and store it in its wheeled carry bag in a cool, dry place, away from direct sunlight and extreme temperatures.
• Luci LED: Ensure the solar panel is clean and free of debris for efficient charging.

Risoluzione di prublemi

Specificazioni

Garanzia è Supportu

For warranty information, product support, or to purchase replacement parts, please visit the official Yaheetech websitu o cuntattate direttamente u so serviziu clienti. Riferitevi à a vostra ducumentazione d'acquistu per i termini è e cundizioni specifiche di garanzia.

Yaheetech Store: Visit the Yaheetech Store on Amazon