UNI-T UPO1102 100MHz 2-Channel Digital Oscilloscope Instruction Manual

1. Introduzione

This instruction manual provides essential information for the safe and effective use of the UNI-T UPO1102 100MHz 2-Channel Digital Oscilloscope. The UPO1102 is a versatile instrument designed for electronic and electrical measurements, featuring a 100MHz bandwidth, 1 GSa/s real-time sample rate, 56 Mpts memory depth, and a 7-inch display. It incorporates Ultra Phosphor technology for enhanced waveform display and analysis capabilities.

Please read this manual thoroughly before operating the device to ensure proper functionality and to prevent damage.

2. Informazioni di sicurezza

Always observe the following safety precautions to avoid personal injury and prevent damage to the instrument or other connected devices.

• Cunnette u cordone di alimentazione à una presa di terra currettamente.
• Do not operate the oscilloscope in wet or damp cundizioni.
• Assicuratevi una ventilazione curretta per prevene u surriscaldamentu.
• Ùn aprite micca u strumentu casing; cuntattate u persunale qualificatu per a manutenzione.
• Use only specified probes and accessories.
• Observe all terminal ratings to prevent fire or shock hazard.

3. Produttu Finituview

3.1 Pannellu Frontale

Figure 3.1: Front Panel of UPO1102 Oscilloscope

The front panel features the main display, various control knobs and buttons for waveform adjustment, trigger settings, and menu navigation. Input channels CH1 and CH2 are located at the bottom right.

3.2 Panel posteriore

Figure 3.2: Rear Panel of UPO1102 Oscilloscope

The rear panel includes the AC power input, USB ports for data transfer and printing, and ventilation grilles to ensure proper cooling during operation.

3.3 Dimensioni

Figure 3.3: UPO1102 Oscilloscope Dimensions

The physical dimensions of the UPO1102 are approximately 13.23 inches (width) x 6.46 inches (height) x 4.13 inches (depth).

4. Setup

4.1 Unpacking è Inspection

Upon receiving your UPO1102 oscilloscope, carefully unpack all components and inspect them for any signs of damage. Retain the packaging for future transport or storage.

Accessori standard:

• Oscilloscope Probe (UT-P04) x 2
• Cordone d'alimentazione
• USB2.0 Printing Cable
• English Download Guide
• Multi-language Safety Manual
• Calibration Report (COC)

4.2 Cunnessione di putenza

1. Ensure the oscilloscope is placed on a stable, level surface with adequate ventilation.
2. Connect the provided power cord to the AC power input on the rear panel of the oscilloscope.
3. Inserite l'altra estremità di u cavu di alimentazione in una presa di corrente CA cun messa à terra.
4. Appughjà u buttone d'accensione nant'à u pannellu frontale per accende l'oscilloscopiu.

4.3 Cunnessione è Compensazione di a Sonda

Before taking measurements, it is crucial to compensate the probes to ensure accurate readings.

1. Connect a probe to one of the input channels (CH1 or CH2) on the front panel.
2. Connect the probe tip to the "Probe Comp" terminal and the ground clip to the ground terminal next to it.
3. Press u Auto button. The oscilloscope will automatically adjust the settings to display the compensation signal.
4. Observe the square wave displayed on the screen. If the waveform is not a perfect square (over-compensated or under-compensated), adjust the trimmer on the probe body using a non-metallic tool until a flat-top square wave is achieved.
5. Repeat for the second probe if using both channels.

Figure 4.1: Probe Compensation Waveform

A correctly compensated probe displays a clean square wave. Adjust the probe's trimmer if the waveform shows overshoot or undershoot.

5. Operating Instructions

5.1 Cuntrolli basi

• Pulsante di putenza: Located on the front panel, used to turn the device on or off.
• Manopola multiuso: Used for menu navigation and parameter adjustment. Press to confirm selections.
• Cuntrolli Verticali (CH1, CH2): Adjust vertical position and scale (volts/division) for each channel. "Push to Zero" resets position, "Push to Fine" enables fine adjustment.
• Cuntrolli Orizzuntali: Adjust horizontal position and time base (seconds/division). "Push to Zero" resets position, "Push to Zoom" enables horizontal zoom.
• Cuntrolli di u grillettu: Set the trigger level, mode (Auto, Normal, Single), and force a trigger event.
• Pulsante Auto: Automatically adjusts vertical, horizontal, and trigger settings to display a stable waveform.
• Buttone Eseguisce/Stop: Starts or stops waveform acquisition.

5.2 Waveform Acquisition and Display

The UPO1102 features a 7-inch display and Ultra Phosphor technology for clear waveform visualization, even with complex signals.

Figure 5.1: Ultra Phosphor Display

Ultra Phosphor technology provides a gradient display, where brighter areas indicate more frequent occurrences of the waveform, helping to visualize signal anomalies and variations.

Figure 5.2: Multi-Channel Waveform Display

The UPO1102 can display and analyze two channels simultaneously, allowing for comparison of different signals.

5.3 Funzioni di misurazione

• Misurazione di u cursore: Activate the "Cursor" function to measure time and voltage parameters within a specified area on CH1, CH2, MATH, or REF waveforms.
• Analisi FFT: The UPO1102 features 1Mpts FFT sampling points, enabling frequency domain analysis. Access the FFT function to set frequency range, detection mode, and spectrum marking.


Figure 5.3: FFT Spectrum Analysis

The FFT function transforms time-domain signals into the frequency domain, useful for analyzing harmonic content and noise.

• Navigation Functions: Utilize time navigation, marker navigation, and segment navigation for detailed waveform inspection.

5.4 Digital Decoding

The innovative hardware decoding feature allows for real-time decoding of serial bus protocols. With a deep storage of 56 Mpts, decoding speed is maintained at millisecond levels, preventing delays when viewing decoded data. This function does not affect the waveform refresh rate, maintaining the digital fluorescence display effect.

Figure 5.4: Digital Decoding Example

The decoding feature displays protocol information directly on the screen, simplifying debugging of serial communications.

5.5 Data Storage and Connectivity

• Profundità di memoria: The UPO1102 offers a 56 Mpts memory depth, allowing for capture of long signal durations at high sampi tassi.


Figure 5.5: Memory Depth Indication

A large memory depth is crucial for capturing transient events or long sequences of data without losing detail.

• Connettività USB: Use the provided USB2.0 printing cable to connect the oscilloscope to a computer for data transfer or direct printing.
• Web Access and Control: U dispusitivu sustene WEB access and control, along with SCPI (Standard Commands for Programmable Instruments) for remote operation and automation.

6. Mantenimentu

6.1 Cura Generale

• Keep the instrument clean and dry. Avoid operating in dusty or humid environments.
• Protect the display from scratches and impacts.
• Do not block the ventilation openings on the rear panel.

6.2 Pulizia

Per pulisce l'esternu di l'oscilloscopiu:

1. Disconnect the power cord and all probes/cables.
2. Aduprate un pannu molle dampened with mild detergent and water. Do not use abrasive cleaners or solvents.
3. For the display, use a soft, lint-free cloth specifically designed for electronic screens.
4. Ensure the instrument is completely dry before reconnecting power.

7. Risoluzione di prublemi

This section addresses common issues you might encounter with the UPO1102 oscilloscope. For problems not listed here, contact UNI-T customer support.

8. Specificazioni

9. Garanzia è Support

For warranty information, technical support, or service inquiries regarding your UNI-T UPO1102 oscilloscope, please refer to the official UNI-T websitu o cuntattate u so dipartimentu di serviziu di u cliente.

UNI-T Official Store: Visit the UNI-T Store on Amazon

Please have your product model (UPO1102) and ASIN (B0D7F2D9MS) available when contacting support.