Pro-Ject Debut EVO 2 Turntable Instruction Manual

1. Introduzione

Thank you for choosing the Pro-Ject Debut EVO 2 Turntable. This high-fidelity record player is crafted in Europe by hand, offering an enhanced listening experience. It features a heavy platter, a carbon fiber tonearm with a resonance-damping aluminum bearing block, and an adaptive anti-skating system. The turntable comes pre-mounted with a Pick it MM EVO Moving Magnet Phono Cartridge and includes a DC/AC power generator. This manual provides essential information for setting up, operating, and maintaining your turntable to ensure optimal performance and longevity.

2. Cuntenutu di u pacchettu

Assicuratevi chì tutti l'articuli seguenti sianu inclusi in u vostru pacchettu:

• Pro-Ject Debut EVO 2 Turntable Unit
• Pick it MM EVO Moving Magnet Phono Cartridge (pre-mounted)
• 15V DC 0.8A Power Supply
• Copertura di polvere
• 7'' Singles Adapter
• Cintura di trasmissione
• Contrappesu
• Pesu anti-skating

3. Setup Instructions

Follow these steps carefully to set up your Pro-Ject Debut EVO 2 Turntable.

3.1 Unpacking and Placement

Carefully remove all components from the packaging. Place the turntable on a stable, level surface away from direct sunlight, heat sources, and vibrations.

3.2 Platter and Drive Belt Installation

1. Place the main platter onto the central spindle.
2. Carefully loop the drive belt around the motor pulley and the inner rim of the platter. Ensure the belt is not twisted.

3.3 Cunfigurazione di u bracciu è di a cartuccia

1. Slide the counterweight onto the rear of the tonearm with the numbers facing forward.
2. The Pick it MM EVO cartridge is pre-mounted on the headshell. Attach the headshell to the tonearm and tighten the locking nut securely.
3. Carefully remove the stylus protector from the cartridge.
4. Unlock the tonearm from its rest. Lift the cueing lever.
5. While holding the headshell, lower the cueing lever completely. Do not let the stylus touch the platter.
6. Turn the counterweight until the tonearm floats parallel to the platter. This is the balanced position.
7. Once balanced, return the tonearm to its rest and lock it.
8. Turn only the numbered ring of the counterweight to '0' on the center line. Do not turn the entire counterweight.
9. Now, turn the entire counterweight (including the numbered ring) counter-clockwise until the desired tracking force is set (e.g., 2 grams for the Pick it MM EVO cartridge).
10. Locate the anti-skating dial near the tonearm base. Set this dial to the same value as your tracking force (e.g., '2').

3.4 Dust Cover and Connections

1. Attach the dust cover hinges to the turntable chassis and then carefully place the dust cover onto the hinges.
2. Connect the turntable's RCA output cables to your amplifier's phono input (or a separate phono preamppiù vivu).
3. Connect the ground wire from the turntable to your ampu terminale di terra di u lifier.
4. Plug the 15V DC 0.8A power supply into the turntable and then into a wall outlet.

3.5 Video di cunfigurazione

For a visual guide on the initial setup, please watch the following video:

4. Operating Instructions

4.1 Riproduzione di un discu

1. Mettite un discu nantu à u platu.
2. Select the correct playback speed (33 or 45 RPM) using the speed selector switch.
3. Unlock the tonearm and lift it using the cueing lever.
4. Carefully position the stylus over the desired groove on the record.
5. Abbassate delicatamente a leva di cueing per permette à u stylus di scende nantu à u discu.

4.2 Fermà a riproduzione

1. Alzate u bracciu aduprendu a leva di cueing.
2. Return the tonearm to its rest and lock it in place.
3. Remove the record from the platter.
4. Turn off the turntable using the power switch.

5. Mantenimentu

5.1 Pulizia di u Stilu

Use a soft stylus brush to gently clean the stylus from back to front. Never brush from front to back, as this can damage the stylus.

5.2 Pulizia di u giradischi

Wipe the dust cover and plinth with a soft, dry, anti-static cloth. Avoid using abrasive cleaners or solvents.

5.3 Drive Belt Inspection

Periodically inspect the drive belt for any signs of wear or stretching. A worn belt can affect playback speed and consistency.

6. Risoluzione di prublemi

If you encounter any issues with your turntable, please refer to the following common solutions:

• Nisun sonu: Check all cable connections (RCA, ground, power). Ensure your amplifier is set to the correct input and volume.
• Sonu distortu: Verify that the tracking force and anti-skating settings are correct. Ensure the stylus is clean and undamaged.
• Velocità sbagliata: Confirm the drive belt is properly seated and not worn. Ensure the correct speed (33/45 RPM) is selected.
• ronzio: Check the ground wire connection. Ensure the turntable is placed away from electronic devices that may cause interference.

If problems persist, please contact Pro-Ject customer support.

7. Specificazioni

8. Garanzia è Support

For warranty information and technical support, please refer to the documentation included with your product or visit the official Pro-Ject Audio Systems websitu. Conservate a vostra prova d'acquistu per qualsiasi reclamazione di garanzia.