GUIDA D'INSTALLAZIONE
CSEN1

CSEN1 Combo Sensor Controller

Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)

DESSCRIPTION

The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.

SPECIFICAZIONI

• Frequenza Radio: 2.4 GHz (IEEE 802.15.4)
• Potenza di Trasmissione RF Output: + 20dBM
• Température de fonctionnement : -40°C à +70°C
• Umidità operativa: 10 à 95%, senza condensazione
• Custodia classificata IP66
• Dimensioni: 3.1 "D x 1.6" H (80 mm D x 42 mm H)
• Input Power: 12-24VDC, 35mA max, 840mW
• Scopu di cuntrollu: Operativu
• Environmental: Indoor/Outdoor
• Grau di contaminazione: 3
• Rated Impulse Voltage: 330 V

CONSIDERAZIONI DI DESIGN

Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage di 10V DC.

• Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
• Trascinate i fili di dimming luntanu da e linee AC, se pussibule.
• Massimu di 4 DALI-2/D4i LED Drivers per controller, cunsultate Synapse Support se hè necessariu un rapportu più grande.
• Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
• Ùn muntate micca à un dissipatore di calore o à un driver LED.

NOTA: U driver LED deve supportà a funziunalità DIM à OFF.
AVVERTENZE E PRECAUZIONI

• TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
• The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
• A mancata osservazione di sti struzzioni è avvisi puderanu annullà a garanzia.
• This product must be installed in accordance with national, state, and local electrical codes and requirements.
• If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.

DETTAGLI DI CABLAGGIO DI ZHAGA BOOK 18 SOCKET

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:

• 12-24VDC POWER: Brown
• Common Ground/DALI-: Pink with White Stripe
• DALI+/DIM+: Violet with White Stripe
• Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length

FIGURA 1

ISTRUZIONI PER L'INSTALLAZIONE

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!

1. Se applicabile, sguassate u tappu di sigillatura o u dispusitivu di cuntrollu di l'illuminazione attualmente installatu in u recipiente di l'attrezzatura.
2. Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
3. After alignment, push until the CSEN1 is fully seated within the receptacle.
4. While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)

Nota: Per funziunà bè, assicuratevi chì u controller hè inseritu cumplettamente in u socket è torcia in a pusizione chjusa.
Attenzione: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
FIGURA 2

LED DI STATU

Power LED	Status
Turchinu	On for 3 seconds at Startup, then Off
Stato LED	Status
Rossu	No script on the device
Rossu lampendu	Errore di cumunicazione
Lampeggiante Blu	Communication, No Config
Verde lampeggiante	Normal Operation with Motion
Off	Normal Operation, no Motion

INFORMAZIONI REGULATORI È CERTIFICAZIONI
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Certificazioni Industry Canada (IC): Stu apparatu digitale ùn supera i limiti di Classe B per l'emissioni di rumore radio da l'apparechju digitale stabilitu in i Regolamenti di Interferenza Radio di u Dipartimentu di Comunicazioni di u Canada.
Certificazioni FCC è infurmazione regulatoria (solu USA)
FCC Part 15 Classe B: Stu dispusitivu hè conforme à a parte 15 di e regule FCC. U funziunamentu hè sottumessu à e seguenti dui cundizioni: (1) Sti dispusitivi ùn ponu micca pruvucà interferenza dannusu, è (2) Sti dispusitivi devenu accettà ogni interferenza ricevuta, cumpresa l'interferenza chì pò causà operazione dannosa.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:

• Part 15, Subpart B, per l'equipaggiu di Classe B
• FCC 96-208 cum'è si applica à l'urdinatori persunali è i periferichi di Classe B
• Stu pruduttu hè statu pruvatu à un Laboratoriu di Test Esternu certificatu per e regule FCC è hè statu truvatu per risponde à a FCC, Part 15, Limiti di Emissioni. A documentazione hè attiva file è dispunibule da Synapse Wireless, Inc.

Se l'ID FCC per u modulu in l'involucro di u produttu ùn hè micca visibile quandu hè stallatu in un altru dispositivu, allora l'esterno di u dispositivu in quale hè stallatu stu pruduttu deve ancu vede una etichetta chì riferisce à l'ID FCC di u modulu chjusu. Modificazioni (FCC 15.21):
Cambiamenti o mudificazioni à stu equipamentu chì ùn sò micca appruvati espressamente da Synapse Wireless, Inc., ponu annullà l'autorità di l'utilizatori à operà stu equipamentu.
Patentatu - marcatura virtuale à https://www.synapsewireless.com/about/patents
Per sapè di più visita: synapsewireless.com

CERTIFICAZIONI

Mudellu	CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure)
Cuntene ID FCC	QOQ-GM240P
Contene IC	5123A-GM240P
RoHS 3	2011/65/EU (2015/863)
REACH UE	(CE) No 1907/2006

Controller d'applicazioni certificatu DALI-2

 

Documenti / Risorse

Synapse CSEN1 Combo Sensor Controller [pdfGuida d'installazione CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller

Referenze

• Manuale d'usu